Shopping Cart
0 items
 

WG-2808 Up to 8 Lines FXS SIP IP Gateway

WG-2808 Up to 8 Lines FXS SIP IP Gateway
Click to enlarge
Price: $380.00
Availability: In Stock
Model: WellGate-2808
Manufacturer: WellTech
Average Rating: Not Rated

WG-2808 Up to 8 Lines FXS SIP IP Gateway

Dual IP Stack: IPv6 and IPv4 Simultaneously
Support up to 16 SIP Trunks to register
Enhance existing PABX to VoIP Call
Consistent with WellGate 2504 and 2424S gateway
Flexible Routes Plan, Dial Plan, Digit Manipulation
Redundant Firmware Image

WellGate 2808 is 8-port FXS gateway with SIP protocol IP device which connects up to 8 Lines of analog telephone set (or, analog trunk line of legend PABX) to make or receive VoIP call over Internet or VPN network. This device is not only suitable for legend PABX to enable VoIP call without changing existing cabling, dial plan, and extension number, but also work with IP-PBX and SIP Server directly. Its design, firmware, auto provision and webpage are consistent with WellGate 2504 (4 ports FXS) and WellGate 2424S (24 ports FXS) gateway.

To select up to 16 SIP TRUNK Accounts

WellGate 2808 is appropriate to use 16 VoIP SIP Trunk or IP Centrex service or IP-PBX within offices and remote branch offices. One of 16 SIP Servers (or ITSP Service provider or alternative IP-PBX ) can be configured freely at each line (FXS port ) to make or receive IP Call. It provides up to 16 service platforms according to your dial number or routes plan.

IPv6 VoIP Gateway is ready to Market

IPv6 address was developed for years, however, it was not practical to our life up to now. More and more electronic devices are able to link to IP Network(for instance, Internet of Things, IoT). This makes existing IPv4 address supply in short to global market. Meanwhile, the emerging countries are not able to increase IPv4 address supply due to strong market demand on broadband services. WellGate 2808 is an SIP based FXS gateway which was built-in both IPv6 and IPv4 IP address. Whenever you are ready to deploy IPv6 network, or reserve the future expansion to IPv6 from existing IPv4 address, WellGate 2808 is ready to grow up with you. Both IPv6 and IPv4 addresses are working simultaneously at Voice IP Call. Its flexibility of both IPv6 and IPv4 accept and interwork both addresses on today and tomorrow whenever you need.

Flexible Dial plan and Route Plan Features

WellGate 2808 provides flexible Dial Plan between FXS and SIP IP Trunk (SIP Soft Switch or IP-PBX). Dial Plan is to configure in what condition the digits can be sent out to/from IP network. The dialing inter-digit time before dialing is configurable to meet local PSTN line or PBX’s extension line. Dial Rule is able to detect the prefix code and maximum digits reached and then dial automatically. The Digit Manipulation (DM) allows you to configure matched prefix code, digits length, start and stop digit position to be replaced digits as well.

Route Plan is to configure the incoming and outgoing call routes which you want this call to go out or allow to income. For instance, IP incoming call may reach to one FXS port with Priority or Cyclic access. You can also configure IP incoming call by Matched prefix digits, matched dialing number to FXS line and Matched digit length. From FXS outgoing call to SIP IP routes, the hunting type supports Priority or Cyclic or Simultaneously to select which SIP trunk ( SIP Proxy Server, or IP-PBX ) to go. FXS outgoing call routes also support by Matched prefix digits, Matched outgoing SIP Trunk number and Matched digit length. Both directions support No Answer time out and Backup Routes.

Upgrade existing PABX to enable VoIP call

WellGate 2808 is a SIP IP device to connect with existing PABX and enable to make or receive VoIP call without affecting existing cabling, extension number or dial behaviors. It is an easy and quick way to upgrade existing PABX to VoIP calls. No need to expand your PABX’s extension lines and analog trunk lines.

 

SPECIFICATION

Interface:

Ethernet port (RJ-45, 10/100 base-T)

1-WAN port, connect to IP Network

1-LAN port connect to PC with NAT

Support Bridge, NAT and Gateway mode

Telephony port connect to local analog line (RJ-11 x 8 pcs)

DC +12V power input Jack

LED Indicator for System, SIP, and FXS status

IP Network connection

IPv4 (RFC 791) and IPv6 Simultaneously

IPv6 Auto Configuration (RFC 4862)

IPv6 Only, IPv4 Only or dual stack

MAC Address (IEEE 802.3)

MAC Clone Setting

Vendor Class ID

IP/ICMP/ARP/RARP/SNTP

Static IP

DHCP Client (RFC 2131), WAN port

DHCP Server, LAN port

NAT Server (RFC 1631)

PPPoE Client

DDNS (DynDNS )

DNS Client

Firewall

URL Filter

IP Filter

MAC Address Filter

Application program Filter

Port Filter

Port Forwarding (TCP, UDP or both)

Bandwidth Control (Download and Upload), Maximum Bandwidth priority setting

UPnP Server at LAN port

Behind NAT, use DMZ for NAT traversal

SNTP with time zone and Daylight Saving

TCP/UDP (RFC 793/768)

RTP/RTCP (RFC 1889/1890)

IPV4 ICMP (RFC 792),

TFTP Client

VoIP VLAN Support 802.1Q, 802.1P

VLAN ID Range : 2 to 4094

VLAN Priority : 0 to 7 (Highest Priority)

QoS : DiffServ (RFC 2475), TOS (RFC791, 1394)

SIP Protocol :

RFC3261 compliance

Support up-to 16 SIP Trunk to Register

SIP UDP Protocol

Support SIP compact Form

Support SIP HOLD Type: Send Only, 0.0.0.0 or inactive

SIP Session Timer (RFC 4028)

SIP Session Refresher: UAC or UAS

SIP Encryption

MD5 Digest Authentication (RFC2069/RFC2617)

Reliability of provision response PRACK (RFC3262)

Early/Delay Media support

Offer/Answer (RFC3264)

Message Waiting Indication (RFC3842)

Event Notification (RFC3265)

REFER (RFC3515)

Support Outbound Proxy

Support Primary and Backup SIP Server

Support STUN NAT Traversal

Support “rport” parameter (RFC 3581)

Configure SIP local Port

SIP QoS Type: DiffServe or QoS

Accept Proxy Only : YES or NO

Audio Codec :

G.711 A-law/μ-law, G.729A, G.723.1 (6.3K, 5.3K)

Select voice codec priority: Local or Remote

Voice Payload size (ms) configuration

Silence Suppression

VAD/CNG

LEC : Line Echo Canceller

Max Echo Tail Length (G.168): 32, 64 and 128ms

Packet Loss Compensation

Automatic Gain Control

In-band/out of band DTMF (RFC4733, RFC2833 / SIP INFO)

Adaptive/Configurable Jitter Buffer

G.168 Acoustic Echo Cancellation

Configure RTP basic Port

RTP QoS Type : DiffServ or TOS

Phone Book (50 records) for peer to peer calls

Dialing Plan with drop, replace, Insert dialing digits

Select First digit and Inter digit timeout duration (Sec)

Selectable Call Progress Tone

Support Specified Line Calling

Call Features :

Support Peer to Peer Dialing

Up to 8-port FXS connects to analog phone set or analog trunk of PBX.

Caller ID generates DTMF (before/after 1st ring) and FSK (before 1st ring ), ETSI and Bellcore

DTMF Caller ID start and stop BIT configurable

Current Drop generation to FXS analog devices

Disconnect tone generation

Tone Generation: Ring Back, Dial, Busy, call waiting, ROH, Warning, Holding, Stutter dial tone and disconnect tone

Configure Tone Frequency, Cadence, Level and Cycle

Select Tone specification by Country name List

Global Country Based Tone Specification

NAT Traversal support STUN, UPNP and Behind NAT

Out-Band DTMF : RFC2833 and SIP Info

RFC2833 Payload type : 101 or 96

DTMF send out ON and OFF Time configure

DTMF incoming recognition Minimum ON and OFF time

DTMF Relay Volume configuration

T.38 FAX Volume configuration

Flash Time transmit via SIP Info (Enable or Disable)

Message Waiting Indication (Stutter Tone Notice)

Block Anonymous Call

Call Hold

Call Transfer

FXS Line Configuration:

Activate or deactivate

Line ID

Line Phone number

Polarity Reversal generation for call establish and Billing.

Current drop generation to release line

Incoming call Handle: Hotline or 2 stage dialing

HOT Line to desired phone number

Recognize FLASH TIME from analog device

T.38 or FAX Relay Type

Incoming and outgoing volume in dB configurable

Dialing Answer Delay time to establish call path

Caller ID generation mode by Country selection

Outgoing SIP Caller ID Selection
Support 16 SIP Trunk
Accept desired SIP Proxy incoming calls Only (Avoid hacker’s call)
Flexible Routing Plan :
Prefix Match and Length
Priority Ring
Cyclic Ring
Simultaneous Ring
Programmable Hunting Cycle
Backup Routes with Digit Manipulation
Default Routes
Flexible Dial Plans :
Retrieve transfer call from 3rd party by dial Code (default: *#)
Inter digit time out setting
First digit dial out delay time setting
End of dial keypad number
Dial Rule : Match dial Prefix and Maximum digits length ( 1-15 )
Phone Book can be Exported or Imported
Digit Manipulation (Drop and Replace Rule):
FXS DM Group
VoIP DM Group
DM 1 Group
DM 2 Group
DM 3 Group
DM 4 Group
Matched Prefix
Matched digit length
Replace digit start position
Replace digit stop position
Replace number
FXS Analog 2-wire interface :
Flash Time Detection: range from 80 to 800 ms
ON-HOOK Voltage -48Vdc
Configure Ring Cadence, Frequency and Voltage
Support Polarity reversal to start Billing
Service Up to 1 Kilo-meter distance to analog telephone set
Generate Current Drop Time (Open Loop Disconnect time)
MANAGEMENT :
Administrative Telnet CLI and HTTP, HTTPS
HTTP provision through MAC address
Multilingual Web User Interface
3 Levels of User Access Right with Password protection with different Web Language (Administrator, Supervisor and User)
HTTP/HTTPS Service Access limitation from WAN port
Configure Service ports at HTTP, HTTPS and Telnet Services
Phone Debug Module: Device Control, Call Control, DB, Verbose
SIP Debug Module: Register, Call, SIP Message, Others
SNTP Debug Module
Device Debug Module
DSP Debug
Provide 8 Debug Levels :
Emergency
Alert
Critical
Error
Warning
Notice
Information
Debug
Provides System Status Logs
Connect to external SYSLOG Server
Status display: Network, Line, SIP Trunk status
Diagnostics (debug through Syslog Event Notice)
Debug in real time by Telnet
Auto Provision via HTTP Server
SNMP V2/Trap
Configuration Backup/Restore
Dual Firmware Image Backup
 
Environmental :
Physical Dimension: 44(w) x 4.5(h) x 11(d) CM.
Weight: 2.3kg (One unit with packing)
 
Operating Temp. & Humidity
- Temp.: 0°C~45°C (32°F~113°F)
- Humidity: 10%~90% relative humidity, non-condensing
Maximum Power Consumption: 17 Watts (1.5A at 12Vdc)
Power Adaptor: - INPUT: AC100V~240V, 50/60Hz - OUTPUT: DC 12V, 3.0A
Approvals: CE, FCC (Part 15, Class B), LVD and RoHS
Country of origin: Made in Taiwan
 
Packing Accessories
WellGate 2808 main unit x 1 pcs
AC to DC+12V Power adaptor x 1 pcs
Rack Mount bracket x 2 pcs
Warranty -One year

 

R&R GROUP INTERNATIONAL

Taipei Taiwan, Hong Kong, Dubai UAE

E-mail: [email protected]
http://www.shop-wifi.com

Write Review
Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad            Good

Enter the code in the box below:

There are no additional images for this product.